Thứ Năm, 30 tháng 6, 2011

MODEL: MIX2488Ⅱ MIX3288Ⅱ MIX4088Ⅱ

MIX
FROM:BIEMA AUDIO | TIME:2011-2-21 15:31:25 | visits:175
600×328

Biema Audi confluen SERIES live console
MODEL: MIX2488Ⅱ MIX3288Ⅱ MIX4088Ⅱ


Specification overview
Input Impedance
Mono Channel Inputs
Phantom On
>2.2k(balanced)
Phantom Off
>12k(balanced)
Stereo Channel Inputs
>7.5k
Insert Returns
>10k
Input Gain(all faders at 0dB)
Mono Channel a or b Inputs
Continuously variable from +10dB to +75dB
Mono Channel a or b Inputs+PAD
Continuously variable from -20dB to +45dB
Mono Tape Inputs
10dB
Stereo Channel Inputs
Continuously variable from -10dB to +10dB
Talkback Input
Continuously variable from +10dB to +60dB
Pink/osc Noise
Continuously variable from -10dB to +10dB
Maximum Input Level
Mono Channel a or b Inputs
+11dBu
Mono Channel a or b Inputs+PAD
+32dBu
Mono Tape Inputs
+21dBu
Stereo Channel Inputs
+21dBu
Talkback Input
+11dBu
CMRR at 1kHz
Mono Channel a or b Inputs(Gain+40dB)
>80dB
Mono Channel a or b Inputs+PAD(Gain+40dB)
>50dB
Frequency Response(20 to 20 kHz)
Mono Channel a or b Inputs MIX(Gain+40dB)
+0dB to -1dB
Noise (20 to 20 kHz)
Mono Channel a or b Inputs (Gain+75dB)EIN ref. 150Ω
-128dBu
System Noise (20 to 20 kHz)
Summing Noise(40 channels routed with faders down)
-85dBu
MIX Noise(40 channels routed with 0dB,pan centre)
-77dBu
Distortion at 1 kHz
MIX outputs(+40dB gain, 0dBu output)
<0.05%
Crosstalk at 1kHz
Channel to MIX
<-85dB
Maximum Fader attenuation
>90dB
Output Impedance
All Line Outputs
100 Ohms Balanced source to drive >600 Ohms
Headphones
To drive >8 Ohms
Maximum Output Level
ALL Line outputs
+21dB
Headphones
+21dB
Nominal Signal Level
Mono Channel a or b Inputs
-75dBu to -10dBu
Mono Channel a or b Inputs+PAD
-45dBu to +20dBu
Mono Tape Inputs
-10dBu
Stereo Channel Inputs
-10dBu to +10dBu
Talkback Input
-60dBu to -10dBu
Equaliser mono channels
Hi pass
Slope
12dB/0ct 12dB
Frequency
-3dB at 80Hz
HF
Gain
Continuously variable from -15dB to +15dB Centre detent=0dB
Slope Freq
Continuously variable -3dBpoint from 2kHz to 20kHz
Wave Centre Freq
Continuously variable Centre from 2kHz to 20kHz
HMF
Gain
Continuously variable from -15dB to +15dB Centre detent=0dB
Freq
Continuously variable Centre from 1.2kHz to 12kHz
Q
Continuously variable from 1.8 to 9
MF
Gain
Continuously variable from -15dB to +15dB Centre detent=0dB
Freq
Continuously variable Centre from 800Hz to 8kHz
Q
Continuously variable from 1.8 to 9
LMF
Gain
Continuously variable from -15dB to +15dB Centre detent=0dB
Freq
 
Continuously variable Centre from 150Hz to 3kHz
Q
Continuously variable from 1.8 to 9
LF
Gain
Continuously variable from -15dB to +15dB Centre detent=0dB
Slope Freq
Continuously variable -3dB point from 20Hz to 550Hz
Wave Centre Freq
Continuously variable Centre from 20Hz to 550Hz
Equaliser mono channels
HF
Gain
Continuously variable from -15dB to +15dB Centre detent=0dB
Slope Freq
-3dB point 12kHz
HMF
Gain
Continuously variable from -15dB to +15dB Centre detent=0dB
Freq
Continuously variable Centre from 4kHz to 12kHz
Q
Continuously variable from 0.7 to 4
MF
Gain
Continuously variable from -15dB to +15dB Centre detent=0dB
Freq
Continuously variable Centre from 1kHz to 3kHz
Q
Continuously variable from 0.7 to 4
LMF
Gain
 
Continuously variable from -15dB to +15dB Centre detent=0dB
Freq
Continuously variable Centre from 200Hz to 600Hz
Q
 
Continuously variable from 0.7 to 4
LF
Gain
Continuously variable from -15dB to +15dB Centre detent=0dB
Slope Freq
-3dB point 80Hz
Channels Peak Indication
+12dB(pre.Faders)
Channels Signal Indication
-12dB(pre.Faders)
Aux Returns Signal Indication
-12dB(Outputs)
Aux Returns Nom. Indication
0dB(Outputs)
Aux Returns Peak Indication
+12dB(Outputs)
Phantom Power
+48V(balanced)/+12V(unbalanced)

WEIGHT /DIMENSIONS
MODEL
N.W
G.W
Product Dimensions
Shipping Dimensions
MIX2488Ⅱ
76kg
113kg
W1653xD1161xH436
W1769xD569xH1408
MIX3288Ⅱ
91kg
143kg
W1969xD1161xH436
W2085xD569xH1408
MIX4088Ⅱ
106kg
164kg
W2285xD1161xH436
W2401xD569xH1408
MIX POWER 7000Ⅱ 
15.5kg
26kg
W483xD390xH88
W653xD610xH185
 
TAG:
Print || Close
 PREV:Finish!
 NEXT:Finish

Biema Speaker

259×218
MODEL:T110A Powe...


290×362
MODEL:4000TII-2
105×330
MODEL:4000TII-1
138×330
MODEL:2000TII-2
96×330
MODEL:2000TII-1
175×330
MODEL:1000T-2
107×330
MODEL:1000T-1
337×251
MODEL:G08MⅡ
278×186
MODEL:G06MⅡ



1043×1407
MODEL:City1
1043×1407
MODEL:City3
248×202
MODEL:TT+10
228×179
MODEL:TT+8
295×391
MODEL:6000T-2
101×330
MODEL:6000T-1

Biema City3

City3
FROM:BIEMA AUDIO | TIME:2011-2-19 18:12:47 | visits:303
1043×1407

City 1 is composed of 600A and B10.City 3 is composed of 800A and B12.
600A and 800A are coming with rugged aluminum housing.The cabinet is specially designed to reduce stationary wave and achieve more transparent sound.
B10 and B12 are small yet very powerful and high performance woofers.
City 1and City 3 are perfect matches with full range and strong base.The two combinations achieve wide frequency response and stunning audio image.
The connection between the column speaker and the subwoofer is very quick and reliable via the connection pote,marking the whole system exceedingly convenient,flexible and fast installation.


 
City Series Technical data & introduction:
MODELGOLDSANGPRO 800A CITY3MODELGOLDSANGPRO B12 CITY3
Frequency Response180Hz-18KHzFrequency Response40Hz-250Hz
ComponentsBML-T302*8,BMH-1302*1N.W/G..W BML-L1203
Impedance: 8OhmImpedance:8Ohm
Long-term power(RMS)150WLong-term power(RMS)300W
Peak PoWER300WAxial sensitivity 1w/1m96db(1w/1m)
Sensitivity 86db(1w/1m)Active Protection circuitry)Opto-limiter,subsonic fillter
Maximum SPL100dbInput sensitivity0.775V
Shipping dimensions(W*D*H)(900*94.5*116.5)mmLow pass turning frequency50-250Hz
N.W/G..W 7.2Kg/8.2KgShipping dimensions(W*D*H)(570*480*380)mm
N.W/G..W 34Kg/38Kg
 
TAG:City3
Print || Close
 PREV:Finish!
 NEXT:City1

GOLDSANGPRO Δ Series Active Line Array system

GOLDSANGPRO Δ Series Active Line Array system
FROM:BIEMA AUDIO | TIME:2011-1-16 14:45:15 | visits:4140098
400×575

GOLDSANGPRO Δ Series Active Line Array system Introduction
Goldsangpro Δ series active line array system is composed of an active subwoofer and passive mid & high line array speakers. The speakers can be either hoisted or ground stacked as a line array. The system has the advantage of easy and flexible installation because of small cabinets.
There are two models of Δseries line array system: Δ-a &Δ-b. Δ-b is the subwoofer comprising 2 pieces
of 8" LF loudspeakers while Δ-a is the mid & high speaker comprising 2 pieces of 4" MF loudspeakers
and 1 piece of pro-ribbon HF driver.
Biema engineers made a grate effort in creating the new technology for accomplishing the system. Δ
series is not just a simple active speaker system. It possesses distant PC control for the line array
speakers, phrase, delay, EQ, crossover, level control functions, etc. One piece of Δ-b can drive four pieces
of Δ-a. It satisfies the basic application of a line array.
Goldsangpro Δ series active line array is specially designed for vocal reinforcement. It is best for
small-to-medium conference room, KTV and pint-sized performance venues.


Δ -b Active Line Array System:
Biema proprietary aluminium rigging hardware and suspension frame
High-density noise absorbable materials
Quick and easy rigging
Proprietary Plane coverage dispersion technoloy
Specialized flight cases for transportation protection
Professional power supply and connection
Environmental black lacquer coating
Special-designed round perforation steel grille
7-ply birch laminate construction
HI-FI tone Pro-ribbon tweeter

ΔII-bSERIES ACTIVE LINE ARRAY BACK PANE:

1. XLR signal input
     Can accept balance or unbalance signal:
     Pin1: Ground, Pin2: Positive(+), Pin3: Negative(-)
2. XLR signal output
     Can be connected to the signal input of another speaker :
     Pin1: Ground, Pin2: Positive(+), Pin3: Negative(-)
3.     RS485 Control (with PC software )  
4. Power on LED (Blue)
     This blue LED illuminates as an indication that the amplifier
     is powered up.
5.     Protection LED (Yellow)
     The LED will be lighted when there is a shortcut in the speaker
     or when the amplifier is overloaded.
6. SIG /CLIP HF: HF signal indicator (green), clip indicator (red).
7. SIG /CLIP SUB: LF signal indicator (green), clip indicator (red).
8. High pass level knob
     This knob is used for adjusting the volume. For louder
     sound, please turn it clockwise. For lower sound, please
     turn it anti-clockwise.
9. Low pass level knob
     This knob is used for adjusting the volume. For louder sound,
     please turn it clockwise. For lower sound, please turn it anti-clockwise.
 
10.Voltage selector
     AC115V or AC230V can be selected by using this switch.
     Please select your local electricity power supply voltage before
     connection.
11.Fuse jack (with fuse)
     The voltage selected is 115V, T12A/250V fuse should be used.
     If the voltage selected is 230V,T6A/250V fuse should be used.
     Please check whether the fuse can match with local electricity
     power supply voltage before connection..
12.Power switch
     On/off power switch for the amplifier. When it is set to ON, the
     amplifier is powered up. When it is set to OFF, the amplifier is
     powered off.
13.Power output jack
     This jack is used for linking another cells. The caution for using
     this jack is the same as above.
14.Power input jack
     115V/60Hz or 230V/50Hz can be selected for power input.
     Please mind that different fuses should be used for different
     voltages. Check whether the fuse can match with local
     electricity supply voltage before power on the unit.
15.Cooling fans
     The fan ventilation holes can not be blocked on any occasions.
16.HF amplifier output:
     Output speaker to satellite.
17.Ventilation gaps
     The ventilation gaps can not be blocked on any occasions.


 Δ-b Series active line array configuration:

Δ-b Drawing for frequency response and impedance:

 Δ-b Series active line array system
 Δ-b SPECIFICATION:
 System
 Active subwoofer
 Configuration
 Construction
 LF unit
 2 pieces 8" (φ50mm) mid
 Material
 Polo birch plywood
 Exterior protection
 Environmental black lacquer finishing
 Suspension
 Proprietary Biema rigging system
 Front panel protection
 Harden spray finishing round perforation steel grille
  Height Front 264mm
 Product Dimensions
 Width 458.5mm   Depth 537mm
 Shipping Dimensions
 600x650x660mm(WxDxH)
 Weight
 N.W 24kg  G.W 52.3kg(1xΔ-b and 4xΔ-a)
 Frequency response ( ±3 dB)
 1 enclosure 60Hz-250KHz
 Sensitivity(Axis1m/1w)
 Full range 97dB
 Input impedance
 4 ohm
 Continuous Power
 300W
 Max. power
 600W
 Amplifier power
 400W(High)+400(Low)
 nput sensitivity
 0.775V
 Connectors
 1x XLR through out 1x XLR
  Input 2x1/4" TRS input
  Horizontal 100°(50m)
 Dispersion angle
 Vertical 60° (50m)
 
TAG:Δ-b
Print || Close
 PREV:Finish!
 NEXT:Finish

Biema City1

City1
FROM:BIEMA AUDIO | TIME:2011-2-19 18:50:01 | visits:477
1043×1407

City 1 is composed of 600A and B10.City 3 is composed of 800A and B12.
600A and 800A are coming with rugged aluminum housing.The cabinet is specially designed to reduce stationary wave and achieve more transparent sound.
B10 and B12 are small yet very powerful and high performance woofers.
City 1and City 3 are perfect matches with full range and strong base.The two combinations achieve wide frequency response and stunning audio image.
The connection between the column speaker and the subwoofer is very quick and reliable via the connection pote,marking the whole system exceedingly convenient,flexible and fast installation.

  

City Series Technical data & introduction:
MODEL
GOLDSANGPRO 600A CITY1MODELGOLDSANGPRO B10 CITY1
Frequency Response180Hz-18KHzFrequency Response45Hz-300Hz
ComponentsBML-T302-6,BMH-1302*1Bass  woofer  BML-L1003
Impedance:      8OhmImpedance:8Ohm
Long-term power(RMS)120WLong-term power(RMS)250W
Peak PoWER250WAxial sensitivity 1w/1m92db(1w/1m)
Sensitivity 84db(1w/1m)Active Protection circuitry)Opto-limiter,subsonic fillter
Maximum SPL98dbInput sensitivity0.775V
Shipping dimensions(W*D*H)(700*94.5*116.5)mmLow pass turning frequency50-250Hz
N.W/G..W  5.7Kg/6.7KgShipping dimensions(W*D*H)(520*405*380)mm
N.W/G..W 29Kg/33Kg
 
TAG:City1
Print || Close
 PREV:City3
 NEXT:Finish

GOLDSANGPRO Σ SERIES ACTIVE LINE ARRAY SYSTEM

GOLDSANGPRO Σ SERIES ACTIVE LINE ARRAY SYSTEM
FROM:BIEMA AUDIO | TIME:2011-1-16 14:35:56 | visits:5100078
290×408
GOLDSANGPRO Σ SERIES ACTIVE LINE ARRAY SYSTEM
★ Biema proprietary aluminium rigging hardware  and suspension frame
 Highly noise- absorbable materials
 Quick rigging
 Proprietary design of the compressed HF  horn
 Proprietary Plane MF compressed  technology
★ Specialized flight cases for transportation  protection (Two speakers each case)
 Specialized power distributor splitter and  connecting cable
 Environmental grey lacquer finishing
 Super-hard sprayed paint steel grille
 9- ply birch laminate construction
 It satisfies the medium venues

Σ SERIES ACTIVE LINE ARRAY SYSTEM BACK PANEL


1. XLR signal input
Can accept balance or unbalance signal:
Pin1: Ground, Pin2: Positive(+), Pin3: Negative(-)
2. XLR signal output
Can be connected to the signal input of another speaker :
Pin1: Ground, Pin2: Positive(+), Pin3: Negative(-)
3. Protection LED (Yellow)
The LED will be lighted when there is a shortcut in the
speaker or when the amplifier is overloaded.
4. Limiter LED (Red)
The LED lights which means the input signal level is too
high. The incoming signal level should be turned down.
5. Signal LED ( Green)
The LED will be lighted when there are incoming signals.
6. Level knob
This knob is used for adjusting the volume. For louder
sound, please turn it clockwise. For lower sound, please
turn it anti-clockwise.
7. Voltage selector
AC115V or AC230V can be selected by using this switch.
Please select your local electricity power supply voltage
before connection.
 
8. Fuse jack (with fuse)
f the voltage selected is 115V, T8A/250V fuse should be used. If the voltage selected is 230V, T4A/250V fuse should be used. Please check whether the fuse can match with local electricity power supply voltage before connection.
9. Power switch
On/off power switch for the amplifier. When it is set to ON, the amplifier is powered up. When it is set to OFF, the amplifier is powered off.
10. Power on LED (Blue)
This blue LED illuminates as an indication that the amplifier is powered up.
11. Power input jack
115V/60Hz or 230V/50Hz can be selected for power input. Please mind that different fuses should be used for different voltages. Check whether the fuse can match with local electricity supply voltage before power on the unit.
12. Power output jack
This jack is used for linking another cells. The caution for using ths jack is the same as above.
13. Cooling fans
The fan ventilation holes can not be blocked on any occasions.
14. Ventilation gaps
The ventilation gaps can not be blocked on any occasions.

Σ SERIES ACTIVE LINE ARRAY CONFIGURATION:

Σ DRAWING FOR FREQUENCY RESPONSE :

Σ TECHNICAL DATA & INTRODUCTION:  

System Configuration
Two-way , full range
 
Sensitivity
( Axis 1m / 1w )
103dB(Full range)
Construction
 
LMF unit
2 x BML-L1001
 
 
HF unit
2 x BMH-4402
Continuous Power
800W
Material
Polo birch plywood
Max power
1600W
Exterior protection
Environmental black lacquer finishing
Peak power
3200W
Suspension
Proprietary Biema rigging system
Dispersion Angle
Horizontal
90°(100m)
Front panel protection
Harden spray finishing hexangular
perforation steel grille
Vertical
8°(150m)
 
Packing
Flight cases with wheels or without
wheels(one speaker each case)
Product Dimensions
(±1.0mm)
Height
Front 322.0mm
Other suspension Accessories
(Wire cables)
 
Iron Frame(One per group)
Electric crane(One per group)
Nylon harness(One per group)
Water-proof canvas
Power distributor splitter(120A)
 
 
 
 
Rear 223.0mm
Width
900.0mm
Depth
655.0mm
Shipping Dimensions
986x773x529mm(without wheels)
986x773x390mm(with wheels)
N.W
56.5kg
Amplifier power
800W /4 ohm
G.W
88.5 kg(with wheels)
nput sensitivity
0.775V
81.0kg(without wheels)
Power
115V/230V 50-60Hz
Frequency response ( ±3 dB)

 
TAG:
Print || Close
 PREV:Finish!
 NEXT:Finish