Wire/Adapter Conversions Identifying Different Video Connectors

Wire/Adapter Conversions

Identifying Different Video Connectors

Wire Conversion table

		From
		Coaxial	Composite	S-Video	Component	VGA	DVI-A	DVI-I	DVI-D	HDMI	DisplayPort
To	Coaxial	Same	RF Modulator	RF Modulator	RF Modulator
	Composite	TV Tuner	Same	Wire/Adapter	Converter Box	Wire/Adapter				Converter Box
	S-Video	TV Tuner	Converter Box	Same	Converter Box	Wire/Adapter				Converter Box
	Component	TV Tuner	Converter Box	Converter Box	Same	Wire/Adapter				Converter Box
	VGA		Converter Box	Converter Box	Converter Box	Same	Wire/Adapter	Wire/Adapter		Wire/Adapter	Wire/Adapter
	DVI-A					Wire/Adapter	Same	Wire/Adapter
	DVI-I						Wire/Adapter	Same
	DVI-D		Converter Box	Converter Box	Converter Box			Wire/Adapter	Same	Wire/Adapter	Wire/Adapter
	HDMI		Converter Box	Converter Box	Converter Box	Converter Box		Wire/Adapter	Wire/Adapter	Same	Wire/Adapter
	DisplayPort							Wire/Adapter	Wire/Adapter	Wire/Adapter	Same

Using this table

• Wire/Adapter: This conversion is simple and can be done in a wire or with a small adapter connected to the wire. This is the preferred low cost solution.
• Converter Box: This conversion requires a stand-alone box. Sometimes these boxes require power as they are effectively very small computers or video cards. Sometimes, the cost of a converter box outweighs the desire to convert the wire. It might be cheaper to buy a new DVD player than to try to convert the wires coming out of the one you have.
• TV Tuner: This is a special type of converter box that selects one specific channel from a coaxial cable.
• RF Modulator: This is a special type of converter box that converts the input into a specific TV channel - usually Channel 3.

You may notice that you might need two converters to get what you need. For example: DVI-I converts to VGA which converts to Component, but you can't find a cable to convert directly from DVI-I to Component. This should be technically possible. The only reason you don't find this adapter is because there isn't enough demand for it. 

DisplayPort should be able to convert to anything that HDMI can convert to. The only reason there are less options in this area is because the cable is too new. This will soon change. 

HDMI & DisplayPort cables also carry audio signals. Converting this cables will probably cause the audio signal to be lost. 

Identifying Different Audio Connectors

Coaxial Adapters

RF Modulator	Converting Composite, S-Video or Component to Coaxial Cable	RF Modulators can convert Composite or S-Video inputs into Coaxial output. Most RF Modulators will only output the video on Channel 3 or 4, but some actually let you pick any channel up to 125. Both Composite and S-Video cables are limited in how long the cables can be. Coaxial cable doesn't have this problem and it is much cheaper.  If your television only has one Coaxial input and it is already in use, then you can use an A/B switch to switch between 2 different Coaxial inputs. Another alternative is to combine both Coaxial wires. SeeReverse Coaxial Splitter as Combiner for more information.
Coaxial AB Switch	Switching between 2 Coaxial Inputs	If your television only has one Coaxial input and it is already in use, then you can use an A/B switch to switch between 2 different Coaxial inputs.
Reverse Coaxial Splitter as Combiner	Combining 2 Coaxial Inputs	Under special circumstances, coaxial cables can be combined. Say you have a Coax feed from a RF Modulator with a signal only on Channel 3. You also have an antenna/cable/satellite feed and there is no station on channel 3. Then, you can theoretically combine the 2 coaxial feeds into 1 by using a Coaxial splitter backwards. Change to channel 3 to watch the video from the RF Modulator. Watch the other channels as normal.  If you are going to attempt to do this, you should get a RF Modulator that lets you pick any channel. Just because there is no station on a given channel doesn't mean that there isn't any noise on that channel. By having a RF Modulator that lets you pick any channel up to 125, there is a very good chance you will be able to find an open clean channel. You may also need to get a filter to clean/remove the noise from the antenna/cable feed to be able to properly combine the Coaxial feeds. The filter will cost more, but combining the feeds is better than having to manually use the A/B Switch to change between inputs.
Coaxial Splitter  Splitter + Amplifier	Splitting a Coaxial Cable from Antenna/Cable Box/Satellite Receiver into 2 Outputs	Splitting Coaxial wire is simple. You can find splitters that will split into 2, 4 or more lines. Using a splitter will degrade the signal strength, and sometimes a cable booster/amplifier will be required. To make things easy, there are all-in-one booster/splitter units.  You cannot use a splitter on a Coaxial wire coming directly from the Satellite Dish. You must use a multiplexer instead.
Satellite Multiplexer	Splitting Coaxial Signals from a Satellite Dish	Splitting cable for satellite is much more complicated. A multiplexer is required to split a satellite signal. A single satellite dish may produce 2, 3, 4 or more coaxial outputs, each one carrying a different signal. You may even have multiple satellite dishes to get all the channels you want. Simply splitting one of these wires for 2 different televisions will not work. A multiplexer will take all of the satellite wires and produce additional outputs. The capabilities of a multiplexer are written as 2x4 (converts 2 wires into 4) or 5x8 (converts 5 into 8). When purchasing a multiplexer, make sure it will work with your service (DirecTV / DishNetwork), and realize that some of the inputs may be dedicated for a local channel antenna or for international satellites and might not suit your needs.

Other Adapters

Splitting Composite Signals			Splitting Coaxial wire is as simple as using a Y RCA splitter. To split a audio/video signal, you will need 3 splitters: one for the video (yellow), one for the right audio (red), and one for the left audio (white). There is some signal loss when splitting composite wire or when running composite wires a long distance.
Converting VGA to Component			If you have a computer with a VGA output that you want to connect to a TV that has Component but not VGA input, then you might be able to use a VGA to Component Converter Box.
DVI to HDMI	HDMI to DisplayPort	DVI to DisplayPort	You can easily convert between DVI, HDMI, and DisplayPort connectors. This might be necessary if you are connecting a computer to a TV. You can use a standalone Converter Box or a wire that converts the signal. There are many types available. Note that the capabilities of each are not the same, so you are limited to the the lowest denominator. Ex: HDMI & DisplayPort carry digital audio, DVI does not. DisplayPort supports a higher resolution & refresh rate...
Composite / Component to BNC		BNC to Composite / Component	BNC cables are sometimes used in place of Composite or Component cables. You will know from either the coloring or labeling what type of cable it is. Red, Yellow, White (Right, Left, Video) for Composite or Green, Blue, Red (Y, Pb, Pr). BNC connectors have either pins or holes on the sides of the connector. Line up the pins with the hole and give the connector a half twist to secure it.